Chapadora de cantos Cehisa (España) 305

Marca:  Cehisa (España)
Modelo:  305
Descripción: 
  • Encolar por calderín de cola termofusible.
  • Tijeras para el corte del canto en rollo.
  • Grupo de retestar.
  • Grupo de refundir de desbaste.
  • Grupo de refundir de acabado.
  • Grupo rascador de radio.
  • Grupo pulidor.
  • Normativa CE
Localización:  La Garriga (Barcelona)
País:  España
Estado:  Segunda mano
Actualizado:  22/02/2020 17:32:05
  +34‑‑938714507   

Introduzca aquí sus datos para contactar con el anunciante

Mensaje al anunciante

 Marcar todos
 Autorizo el envío de newsletters y avisos informativos personalizados de interempresas.net.
 Autorizo el envío de comunicaciones de terceros vía interempresas.net
 He leído y acepto el Aviso Legal y la Política de Protección de Datos.

Previous Next
Cargando...
Doing business in Spain? Interempresas Media is the key
  1. Madera
  2. Chapadoras | Segunda mano Chapadora de cantos Cehisa (España) 305 usado en venta

.
resultados

Marca
gmb
Modelo
País
Italia
Año
Descripción
Size-up 1200 x 880 mm, 820 mm ground clearanceDimensiones: 1200 x 900 x 1300 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 13/11/2020 11:25 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
biesse
Modelo
STREAM B1 9.5
País
Italia
Año
2002
Descripción
Serial number 24453, consisting of: - pre-milling unit RT63 - gluing unit SP20 - stock edge on roll MB2 - end trimming unit EN45 - trimming unit roughing RS10 - trimming unit finisher RF10 - rounding unit AR10 - spindle grooving unit FB30 - end scraping unit RB10 - glue scraping unit RC10 - oscillating brushing unit SZ30 - hair dryer heating unit PH10 - automatic insertion slats group - electronic control BIESSE EDGE NC410 deluxe - WITH DOCUMENTATION Belt width 80 mmDimensiones: 10700 x 1800 x 2300 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 13/11/2020 11:39 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
fravol
Modelo
País
Italia
Año
Descripción
Roll Height: 70 mm, table dimensions of 1.140 x 980 mmDimensiones: 1800 x 1100 x 1100 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 13/11/2020 11:37 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
-
Modelo
País
Suiza
Año
Descripción
Thickness predominantly 0.9 mm, various lengths and strip widths, predominantly 110 to 130 mm wide, wood types cherry, fir, oak, ash and sapeliDimensiones: 6000 x 2500 x 2000 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 19/10/2020 13:49 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
cehisa
Modelo
M402
País
Serbia
Año
2007
Descripción
Panel thickness :8-60 mm, edge thickness :0,3 -8 mm panel width min 75 mm panel length min. 120 mm Infinitely variable feed speed End trimming station type vertical V8; swiveling 0-10 * 2 motors Fine milling units, 0-20 * swiveling Buffing unit Dimensiones: 3600 x 900 x 1700 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 22/10/2020 13:20 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
idm
Modelo
SINGLE 89
País
Italia
Año
1990
Descripción
Serial PLG1089, with glue pot and trimming edges, edging 45 ° possibilityDimensiones: 1800 x 1100 x 1400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 13/11/2020 10:36 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
Optimat KAL 310/7/A20/S2
País
Alemania
Año
2005
Descripción
HOMAG Optimat KAL 310/7/A20/S2 Edgebander without refeed systemDimensiones: 10000 x 1500 x 1700 mmEstado: funcionandoCondiciones de entrega: cargado en camiónFinal de la subasta: 06/11/2020 10:00 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
egurko ortza
Modelo
UK 16/11D
País
España
Año
2000
Descripción
Chapadora de Cantos EGURKO ORTZA, altura de trabajo: 900 mm, presión de trabajo: 6 bar, longitud mínima de pieza: 80 mm, longitud mínima de pieza con listón: 180 mm, longitud mínima de listón: 200 mm, longitud máxima: 8000 mm.Dimensiones: 8100 x 1350 x 2300 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 27/10/2020 10:09 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KL 77/QA
País
Alemania
Año
1992
Descripción
Work-piece width min. 90 mm height of work piece min-max 7-60 mm edge thickness min. max. 0,4-12 mm feed 10-40 m/min. feed speed infinitely variable work-piece overhang 50 mm stop side left glue indication glue roller gluing aggregate hot melt glue edge magazin roller 3 edge magazin strips magazin massive 12 pressure zone straight snipping chamfer-straight flush milling 1 chamfer / radius milling 2 universal trimming unit 2 profile sliding blade bottom 1 buffing aggregate top/bottom 1 electronic control connection 380 volts, 50 cyc.Dimensiones: 9000 x 2400 x 2200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:07 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
KD 67 C
País
Alemania
Año
2000
Descripción
Technical data ---------------- edge thickness 0.4 - 8 mm Roll separation max. 3 x 45 mm workpiece thickness 8 - 40 mm workpiece width min. 65 mm workpiece length min. 160 mm Feed rate max. approx. 11 m/min. electrics 400 V - 3 Ph. - 50 Hz Pneumatic connection min. 6 bar connected load approx. 7 kWDimensiones: 5000 x 1300 x 1800 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:31 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
KDF 770 C
País
Alemania
Año
2003
Descripción
Single sided edge banding machine in handicraft right-hand version for hotmelt adhesive gluing. Quick-change gluing unit for hotmelt adhesive. Processing of PU-glue granulate under Observance of the adhesive processing instructions possible. Glue supply leak-proof underneath the glue roll. Fine dosage of glue to the workpiece by means of a glue roller, no adjustment to factory piece thickness required. Glue roll rotation direction either constant or Counter rotation. Glue temperature monitoring by means of electronic thermostat. Automatic glue temperature reduction at work interruptions. Infrared hot-melt adhesive activation. Automatic edge magazine for roll goods and Fixed lengths, incl. roller plate diameter 800 mm. Equipment with reinforced pre-cutting shears for Thick PVC/ABS max. 3 x 45 mm. Standard equipment with edge and factory piece distance monitoring by means of optical Display. Heavy pressure zone with driven, pneumatic table loaded main pressure roller and 3 free-running reprint rolls. Standard equipment with automatic Central lubrication for the transport chain. Centrally adjustable top pressure. Control panel at the machine infeed. Electronic control PC 16 noise protection cladding including central suction connection diam. 160 mm and chip trap box for scraper shavings with suction socket Diameter 100 mm. For machines with a Joining milling unit (KDF machines) additional Suction connection diameter 120 mm. Permissible ambient temperature min. +5 degrees/ max. +35 degrees Celsius. edge thickness 0.4 - 15 m Roll separation max. 3 x 45 mm or 0.8 x 60 mm workpiece thickness 8 - 55 mm Variable feed rate 11 - 20 m/min. feed speed: up to 15 mm edge thickness max. 16 m/min up to 3 mm edge thickness max. 20 m/min. for processing with form milling max. 16 m/min Electrical 400 V - 3 Ph. - 50 Hz Pneumatic connection min. 6 bar connected load approx. 18 kWDimensiones: 6750 x 1200 x 1800 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:30 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KAL310/6/A3/S2
País
Croacia
Año
2004
Descripción
edge thickness:46 mm workpiece thickness:46 mm workpiece width min. [in mm -2200 mm feed [in m/min]:18 m/mm (8-42) joint trimming unit:yes workpiece pre heater:yes gluing unit:yes edge magazine with:yes snipping unit: yes rough trimming unit: yes fine trimming unit:yes profile trimming unit:yes universal trimming unit:yes edge sanding unit:yes flat scraping unit:yes profile scraping unit:yes edge buffing unit:yes control:p. c. refeed system: yes (original) serial number of manufacturer:0-200-19-1132 article number of manufacturer:KAL -310 Dimensiones: 12000 x 3000 x 2600 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 22/10/2020 11:21 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
FKR 79/09/
País
Alemania
Año
1990
Descripción
HOMAG FKR 79/09/ Edgebander equipped as follows: single-sided edge-banding machine work-piece width min. 105 mm height of work piece min.-max. 7-60 mm edge thickness min.-max. 0,4-14 mm feed 10-30 m/min. feed speed infinitely variable work-piece overhang 60 mm stop side right scoring / Chipping 2 pcs standard trimming units 2 pcs soft trimming unit 1 pc glue indication glue roller gluing aggregate hot melt glue edge magazin roller 2 pcs edge magazin strips edge magazin massive 14 pressure zone soft snipping chamfer-straight chamfer / radius milling 3 pcs profile trimming / copying (4 motors) 1 pc universal trimming unit 2 pcs profile sliding blade bottom 1 pc flat sliding blade top/bottom 1 pc buffing aggregate top/bottom 1 pc height adjustment electronically electronic control connection 380 volts, 50 cyc. The loading dimensions have been roughly recorded. If you have a transport request, we must first request it from the seller.Dimensiones: 26000 x 2450 x 2200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:08 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
KDF 660
País
Alemania
Año
2003
Descripción
height of work piece min.-max. 8 - 55 mm edge thickness min.-max. 0,4 - 8 mm feed 14 m/min. stop side right jointing-/profile-trimming 1 pc glue indication glue roller gluing aggregate hot melt glue edge magazin roller 3 edge magazin strips yes edge magazin massive 8 pressure zone straight snipping chamfer-straight chamfer / radius milling 1 profile trimming / copying (2 motors) 1 profile sliding blade bottom 1 flat sliding blade top/bottom 1 buffing aggregate top/bottom 1 height adjustment manually electronic control yes connection 400 volts/50 cycDimensiones: 6400 x 1400 x 1800 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:35 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KFL 21/03/22/QE/25
País
Alemania
Año
1996
Descripción
HOMAG KFL 21/03/22/QE/25 KLM Squaring- and Edgebanding Machine Double-sided HOMAG panel sizing and single- sided edge banding machine. Fixed stop side on the left, movable side on the right. BASIC MACHINE: -------------- - with continuous machine frame and unit beam, prepared for double-sided installation of the panel sizing units and single-sided installa- tion of the edge banding and postprocessing units - glue roller driven in case of feed stop WORKPIECE TRANSPORT DEVICE: --------------------------- - chain conveyour separated on the fixed side - rolling block link chain with ball bearings at running and guiding surfaces - with precise, hardened running and guiding surfaces - magnetic motor braking of the transport chain TOP PRESSURE: ------------- - with driven, continuous compound V-belt - motorized height adjustment via cardan drive with digital position read-out WIDTH ADJUSTMENT OF THE MOVABLE SIDE: ------------------------------------- - linear guide as well as rolling guides on hardened supports - motorized rapid/slow gear drive - ball-screw spindles and cardan drives for precise positioning - digital position read-out ELECTRIC EQUIPMENT: ------------------- Please indicate voltage(basis 380 volt/50 cyc.) - operating voltage ... volt, .. cyc. - control voltage ... volt, .. cyc. - installed according to European Norm EN 60204 - hand switch for setting operation - separate switch cabinet - connection cable to the machine according to the installation plan HOMATIC ELECTRONIC CONTROL: --------------------------- - programmable memory control (PLC) with LED display of all inputs and outputs. Integrated line control for contactless control of the processing units. - multitask control of the PLC for precise unit operation - arbitrary number of workpieces in the machine - compatible interface to all HOMATIC input systems - permissible environmental temperature: min. +5, max. 35 degrees Cels. SAFETY AND PROTECTION FACILITIES: --------------------------------- - all machines destined for EC member countries are fitted with CE plates in accordance with EC Machine Directive 98/37/EC Appendix IIA - Wood dust protection max. 2 mg/m3, subject to the required extraction capacity being provided by the customer according to the suction plan. - documentation TECHNICAL DATA: --------------- - feed infinitely variable 10 - 40 m/min. - workpiece overhang40 mm - workpiece thickness 8 - 60 mm - working height up to upper chain surface950 mm - working height double-sided min. 240 - 270 mm (depending on machine equipment) - working width double-sided max. 2500 mm - pneumatic connection7-8 bar - the technical data for the basic machine may vary due to the processing units. - floor conditions have to correspond to the foundation plan. further equipment: ------------------ 1 x left infeed fence adjustable via steplessly axis 1 x left high-performance packet for feed up to 60 m/min. 27 x left rolling transport chain 8 x left, 8 x right rolling transport chain 20 x left, 20 x right stepless stop cams 1 x left, 1 x right steplessly adjustable stop cams automatic 1 x left infeed device 4 rollers tiltable 1 x left electropneumatic tilting movement 1 x left, 1 x right panel taking over device 1 x left, 1 x right stepless axis vertical for UF 11/12 1 x left, 1 x right chain track extension machine II + 500 mm 1 x left centralized drive for KFL/R21 1 x left stepless axis for overdrive 1 x left cam lowering for separated basic machines 1 x central support automatic for KFL/R21 5 x extension of central support 1 x feed drive with automatic control from 6 kW 1 x left, 1 x right execution D - double top pressure 25 x left extension of double top pressure by one step 4 x right extension of double top pressure by one step 1 x left, 1 x right compact double hogger longitudinal/cross 6,6 kW KD11 3 x left, 3 x right electronic braking from 3,75 - 7,4 kW 3 x left, 3 x right motor shaft D=40 for mounting of hydro clamping 1 x left stepless axis horizontal 1 x left, 1 x right noise protection panel sizing part 1000 mm 3 x left, 3 x right extension noise protectin panel sizing part by 100 mm 1 x left unit beam 500 mm long 16 x left extension unit beam by each 100 mm 1 x left lateral adjustment of unit beam stepless 1 x left panel pre-heating up to 45 mm panel thickness 1 x left hot melt softforming unit QE 34 1 x left glue container back-off in case of feed stop 1 x left hot melt granulate transport system 1 x left magazine HL 15 - 6 rolls 3,5 mm 1 x left magazine - height adjustment 1 x left edge holding-down device stepless via axis adjustment 1 x left additional kit for hot melt softforming/E 1 x left pressure zone C with 3 post-pressing rolls autom. 8-fold 1 x left adjusting device pressure zone autom. 8-fold 1 x left separating agent spray device top/bottom 1 x left adjusting device autom. 8-fold 1 x left snipping unit HL04 chamfer/straight 1 x left electronic braking from 0,2 - 3,74 kW 1 x left adjusting device chamfer/straight for HL-snipping 1 x left overhang modification HL 04-05 automatic 1 x left standard trimmng unit pnaumatic control 4,5 kW 1 x left electronik braking from 3,75 - 7,4 kW 1 x left stepless axis horizontal 1 x left stepless axis vertical 1 x left hood interlocking for noise protection cover 1 x left trimming column 2 guides 1 x left dividing wall for noise protection cover 1 x left free space approx. 650 mm 1 x left unit beam 500 mm long 23 x left extension unit beam by each 100 mm 1 x left lateral adjustment of unit beam stepless 1 x left pre-trimming unit top and bottom 0,6 kW 1 x left electronic braking from 0,2 - 3,74 kW 2 x left adjusting device trimming motor pneumatic 1 x left trimming unit top and bottom 0,6 kW 2 x left plug type connection for motor max. 1,5 kW 1 x left electronic braking from 0,2 - 3,74 kW 2 x left adjusting device trimming motor pneumatic 1 x left profile trimming unit FF12 bottom/top 0,3 kW 2 x left electronic braking from 0,2 - 3,74 kW 1 x left empty stroke device profile trimming top 1 x left empty stroke device profile trimming bottom 1 x left unit beam 500 mm long 25 x left extension unit beam by each 100 mm 1 x left lateral adjustment unit beam stepless 1 x left profile trimming unit FF12 bottom/top 0,3 kW 2 x left electronic braking from 0,2 - 3,74 kW 1 x left empty stroke device profile trimming top 1 x left noise protection panel sizing part by 100 mm 66 x left extension noise protection panel sizing part by 100 mm 1 x left noise protection door interlocking according to BG-prescriptions 1 x left scraping unit - profile 2 x left adjusting device pneumatic 1 x left scraping unit glue joint 2 x left adjusting device pneumatic 1 x left edge heating device - overstretch crazing 1 x left free space for buffing-aggregat 1 x panel support for single-sided machines 22 x extension panel support 1 x frequency converter 7,5 kVA 300 cyc. IP 54 1 x frequency converter 40 kVA 100 cyc. IP 54 1 x electronic frequency invertor 45 kW 1 x Homatic electronic control ES 00 25 x left extension Homatic electronic control FL 10/20 1 x left electronic height adjustment 1 x left electronic width adjustment Servo EB 10/2 1 x production line control NC50 1 x flexible edge sequence control 1 x resetting in the gap 1 x cooling unit for switch cabinet 1 x software barcode-control for NC 50 1 x left network connectino Ethernet with TCP/IP 1 x left network file system (NFS) under TCP/IP 5.520 1 x cable extension switch cabinet - machine L 30 1 x guiding tube for cable supply from top 1 x cable extension switch cabinet - operator paneDimensiones: 27000 x 2450 x 2400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:09 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
egurko
Modelo
KB-500
País
España
Año
1997
Descripción
Canteadora Monolateral EGURKO KB-500. Compuesta por: - Grupo de encolado. - Grupo de retestado. - Grupo de refilado. - Grupo de rasca canto. - Grupo de cepillos de limpieza. Altura de trabajo: 900 mm. . Longitud min. pieza: 120 mm. Anchura min. pieza: 120 mm. Espesor max. pieza: 50 mm. Velocidad avance de cadena: 12 m/mm.Dimensiones: 6000 x 1200 x 1500 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 27/10/2020 10:41 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
-
Modelo
País
Rumania
Año
Descripción
Disc diameter approx. 400 mm, disc width 50 mm eachDimensiones: 1200 x 1000 x 1400 mmEstado: sin comprobarCondiciones de entrega: franco sobre camiónEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KL 10/08/QA/S
País
Alemania
Año
1997
Descripción
Work-piece width min. 70 mm Work-piece length min. 160 mm Height of work piece min-max 8-60 mm Edge thickness min. max. 0,3-3 mm Feed 10-40 m/min. Feed speed infinitely variable Work-piece overhang 30 mm Stop side left jointing-/profile-trimming 1 glue indication glue roller gluing aggregate hot melt glue edge magazin roller 3 pressure zone straight snipping chamfer-straight chamfer / radius milling 1 universal trimming unit 1 profile sliding blade bottom 1 height adjustment powered connection 400 volts/50 cyc.Dimensiones: 13000 x 2400 x 2200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:13 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
KD 85 FC
País
Alemania
Año
1997
Descripción
BRANDT KD 85 FContour Edgebander Infrared hot-melt adhesive activation integrated line control for contactless control of processing functions Pneumatic adjustment of trimming and scarping unit Dimensiones: 6200 x 1250 x 1850 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 06/11/2020 10:04 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KL 20/15/QA
País
Alemania
Año
1994
Descripción
Precision chain guiding device, width of chain plates 70 x 100 mm driven top pressure with composite belt, motorized adjustable in height workpiece thickness 8-65 mm without corner coining (optional),depending on material and size workpiece thickness 15-35 mm with corner coining (optional),depending on material and size workpiece width min. approx. 70 mm without corner coining (optional) workpiece width min. approx. 120 mm with corner coining (optional) workpiece overhang adjustable, but min. 65 mm with corner coining frequency controlled feed speed, approx. 3 - 10 m/min. without corner coining, depending on workpiece and substrate approx. 3 - 8 m/min. with corner coining (optional), depending on workpiece, panel distance and substrate total length of machine: approx. 9.200 mm infeed with roller rail laterally mounted at chain road, for small parts min. 120 mm 1 x left stop fence, manually lateral adjustable 2 x left Profile sanding unit PS 20 For sanding of profiles, rebates and straight edges swivelling - 45 degrees in case of mounting height 490/570 mm With gap in machine rack +60 degrees with top pressure For sanding in synchronism ? parallel feed . Belt length 3200 mm Belt width 50 - 70 mm Sanding pressure manual adjustable Without sanding shoe. Key switch For motor stop in case of belt changing. Belt scratch control with optical display. Belt emission via nozzle. Sanding belt encapsulation. incl. Frequency control 1 x left Belt sanding unit KS 10 For sanding of straight edges Sanding belt speed 10 m/sec. Belt length = 2100 mm Belt width = 120 mm Sanding pressure manual adjustable Belt emission via nozzle Oscillating device incl. Frequency control 1 x left Free space for lateral mounting of a brushing unit 1 x left blowing-of nozzle 1 x left Touchwood-unit KTF-70/V-2 The Touchwood-unit KTF-70/V is especially designed for installation of Edge processing machines. It coated each kind of profiles at MDF- or solid wood edges. Range of use: Transferfinish-coating in furniture industry Description of functions - The single transfer heads can be separately controlled. - All function parameters are precise adjustable and exact reproduceable. - The carrier foil is automatic removed from the coated edge and wound up. Technical data: Transfer witdh max. 70 mm Working speed max. 5 m/min. per head Electronic temperature regulation 0 - 400°C (each transfer head ) Electrical connection 400 V, 3 Phasen, 50 Hz, 3,5 kW Air connection 6,5 bar Note: Mounted under consideration of a later installation of a corner coining unit. Transfer unit incl. 1 set coining wheels 1 x left Scraping unit glue joint Removal of glue residuals in range of glue joint. Tracing from top and bottom. Height adjustment with top pressure With hard metal knives Blowing nozzles electropneumatic controlled Unit top and bottom max. 50 mm lateral mobile. Incl. Pneumatic control lateral on manual 8-fold turret 1 x left Buffing unit top and bottom For cleaning of changeovers foils and protective layer 2 motors each 0,25 KW Adjustable in height and inclination Height adjustment with top pressure Workpiece thickness max. 60 mm 2 molton discs diam. 150 x 50 x 25 mm 1 switch cabinet, separate, incl. cooling unit 1 operator panel at machine infeed 1 adjustable workpiece support extractable to approx. 700 mm 1 control 170 =============== KUPER MACHINE CONTROL Consisting of : - programmable memory control (SPS) Programmed on basis SIEMENS Step 7 - decentralized periphery of in- and outputs via profibus - LED display of all in- and outlets - integrated line control for contactless Control of processing units - interface for SIEMENS ? input panel Allowed environment temperature min. +5 degrees Celsius max. +35 degrees Celsius KUPER MASCHINE INPUT OP 170 SIMATIC OP 170B with 5,7 backlight display, Bluemode (4 steps), based on operating system Windows CE . - clearly numerical and alphanumerical input possibility - program memory on optional mutimediacard possible, therefore Almost unlimited memory size - fault diagnosis with help texts - via password protected parameters and service levels - language German or English optional if required other languages can be generated - dimension inpu in mm, optional inch Air connection: 1/2 , min. 7 bar, supply min. 1 Attention!!! A transport frame from HOMAG is required for transporting the dismantled machine, for which costs of EUR 2000,- plus VAT will be charged. After return of the transport rack to SURPLEX, the amount will be refunded minus a value reduction of 10 %. The return costs to our warehouse must be paid by the customer. The return address is as follows: Surplex Warehouse Im Hasseldamm 1 41352 Korschenbroich Germany The return must be pre advised one week before delivery. The loading dimensions have been roughly recorded. If you have a transport request, we must first request it from the seller.Dimensiones: 23000 x 2400 x 2200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:12 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KL 59/10/QA
País
Alemania
Año
1993
Descripción
Basic machine with continuous machine rack and workpiece conveying device, prepared for installation of processing units. Unit carrier lateral adjustable for changing of workpiece overhang in the range of 40-115 mm. Precise workpiece conveying device. Top pressure motorized adjustable in height with driven V-belt Electro: operating voltage 380 Volt, 50 cyc. control voltage 220 Volt, installed as per VDE hand switch for one-shift operation Setting-up of switch cabinet and frequency converter as well as length of connection cable as per layout plan. feed infinitely variable 10 - 40 m/min. panel overhang adjustable 40 - 115 mm panel thickness 7 - 60 mm working heigth 905 mm working width min. 70 mm 1 x left, 1 x right transport chain rolling 1 x left execution top pressure with compound V-belts. 1 x left infeed fence lateral adjustable via fence 1 x left infeed device 3 rolls tiltable *********************************** note: the complete gluing-part is missing *********************************** 1 x left glue roller drive in case of feed stop 1 x left hot melt gluing unit QA 34 melting unit with container for granulates melting capacity depending on glue max. 18 - 35 kg/h. electronic temperature adjustment with LED-read-out glue roller diameter 34 mm glue roller heated level control of melting quantity 1 x left panel pre-heating up to 45 mm panel thickness for heating of workpiece edge before glue application for improvement of gluing quality 1 x left magazine HL 21 infeed angle 13 degrees edge thickness 0,4 - 14 mm edge width 16 - 65 mm processing 360 mm2 feed of solid edges feed of strips 1 x left clipping unit for single roll 3,5 mm for HL 20-22 edge thickness max. 3,5 mm edge width max. 65 mm processing max. - in case of PVC 135 mm2 max. - in case of veneer 100 mm2 roll diameter max. 900 mm 1 x left magazine height adjustment for HL 10/11/12/15/20/21/22 adjustment via spindle adjustment way +/- 10 mm 1 x left pressure zone G 1 driven pre-pressure roller diameter 200 mm 6 post-pressure rollers diameter 150 mm pneumatic pressure adjustment for straight edges Centralized adjustment for change-over in case of different edge thicknesses. 1 x left unit carrier with manually lateral adjustment 1 x left snipping unit HL 05 chamfer/straight 0,6 kW 2 motors each 0,6 kW, 300 cyc., 18000 rpm edge thickness straight max. 20 mm chamfer max. 3 mm edge width max. 65 mm 1 x left electronic braking from 0,2 - 3,74 kW 1 x left pneumatic adjusting device chamfer/straight for electropneumatic reset from chamfer to straight snipping. Manual adjustment of lateral snipping stop necessary in case of varying edge thickness. 1 x left Pre-Milling aggregate top/bottom 1,5 KW 2 motors one upon the other, each 1,5 KW, 300 Cy 18000 l/min., manually laterally movable height adjustment with the top pressure, working in counter direction edge thickness max. 20 mm workpiece thickness 7 - 60 mm swivelling area +/- 1 degree 1 x left el. braking from 0,2 - 3,74 KW 2 x left double roll scanning vertically Per motor. Required for radius bigger 3 mm and acute-angled workpieces 1 x left Milling aggregate top and bottom 0,3 KW 2 motors each 0,3 KW, 300 Cy, 18000 l/min. manually laterally movable edge thickness max. 1,5 mm workpiece thickness max. 60 mm Swivelling area 0 - 30 degrees 1 x left el. braking from 0,2 - 3,74 KW 2 x left adjusting device for electro-pneumatic lateral movement to manual 8-fold revolver separate motor starting 2 x left double roll scanning horizontally for lateral scanning of the milling aggregate required for abtuse-angled workpieces 1 x left milling aggregate top and bottom1,125 kw 2 motors ech 1,125 KW, 3000 cy., 18000 1/min. manually laterally movable, height adjustment with the top pressure, working in counter direction edge thickness max 14 mm workpiece thickness max. 60 mm Swivelling area 0 - 30 degrees 1 x left el. braking from 0,2 - 3,74 kw 2 x left adjusting device for electro-pneumatic lateral operation to manual 8-fold revolver separate motor starting 2 x left double roll scanning vertically Per motor. Required for radius bigger 3 mm and acute-angled workpieces 2 x left double roll scanning horizontally for lateral scanning of the milling aggregate required for abtuse-angled workpieces per motor. 1 x left noise protection hood aggregate length approx. 2700 mm, 1 accumulative suction hood diam. 200 mm 1 x left aggregate support with manual lateral adjustment 1 x left milling aggregate top and bottom 1,125 kw 2 motors ech 1,125 KW, 3000 cy., 18000 1/min. manually laterally movable, height adjustment with the top pressure, working in counter direction edge thickness max 14 mm workpiece thickness max. 60 mm swivelling area 0 - 30 degrees 1 x left electronical braking from 0,2 - 3,74 kw 2 x left adjusting device for electro-pneumatic lateral operation to manual 8-fold revolver separate motor starting 2 x left double roll scanning vertically Per motor. Required for radius bigger 3 mm and acute-angled workpieces 1 x left free space for installation of another milling aggregate 1 x left form milling aggregate bottom 0,3 KW 2 motors each 0,3 kw, 300 cy., 18000 1/min. separate motor starting edge thickness max. = 4 mm workpiece length min. = 80 mm with quick-change device for radius/chamfer without tools Change: motors with 0,6 KW instead of 0,3 kw 1 x left electronical braking from 0,2 - 3,74 kw 1 x left form milling aggregate top 0,3 KW 2 motors each 0,3 kw, 300 cy., 18000 1/min. separate motor starting edge thickness max. = 4 mm workpiece width min. = 40 mm max. = 60 mm without working workpiece lenth min. = 80 mm with quick-change device for radius/chamfer without tools Change: motors with 0,6 kw instead of 0,3 kw 1 x left electronical control 0,2 - 3,74 KW 1 x left noise protection hood aggregate length approx. 3100 mm, 1 accumulative suction hood diam. 180 mm 1 x left scraping unit profile scanning from top, bottom and laterally for chamfering and rounding of pre-milled PVC-edges. Blast nozzle electro-pneumatically controlled. Edge thickness max. 5 mm Aggregate top and bottom mx. 50 mm laterally movable. Height adjustment with the top pressure. Without tools. suction box for PVC-chips 1 x left adjusting device milling motor pneumatically for electropneumatic lateral operation to manual 8-fold revolver separate motor starting 2 x left double roll scanning vertically Per motor. Required for radius bigger 3 mm and acute-angled workpieces 2 x left double roll scanning horizontally for lateral scanning of the milling aggregate required for abtuse-angled workpieces per motor. 1 x left scraping unit profile scanning from top, bottom and laterally for chamfering and rounding of pre-milled PVC-edges. Blast nozzle electro-pneumatically controlled. Edge thickness max. 5 mm Aggregate top and bottom mx. 50 mm laterally movable. Height adjustment with the top pressure. Without tools. suction box for PVC-chips Hint: here without suction box 2 x left adjusting device milling motor pneumatically for electropneumatic lateral operation to manual 8-fold revolver separate motor starting 2 x left double roll scanning vertically Per motor. Required for radius bigger 3 mm and acute-angled workpieces 2 x left double roll scanning horizontally for lateral scanning of the milling aggregate required for abtuse-angled workpieces per motor. 1 x left edge heating overstretch crazing flap gate control for the deletion of overstretch crazing with PVC-edges, top and bottom. Consisting of: - air heater with temperature regulation via electronical controller and digital display - flap gate control - protection fence 1 x left Belt sanding aggregate KS 10 for sanding of straight edges sanding belt speed 10 m/sec. belt length = 2100 mm belt width = 120 mm Sanding pressure manually adjustable Belt radiation via nozzle Oscillating device 1 x left Adjusting device belt sanding aggregate pneumatically for electropneumatic lateral movement on manual 8-fold revolver for different edge thicknesses 1 x left chamfer/radius sanding aggregate bottom PS41 1 motor 0,55 kw workpiece thickness min. 12 mm Radius max. 12 mm sanding belt length 2000 mm. Width 20 - 35 mm Belt speed 7 m/sec. Sanding pressure manually adjustable Without sanding shoe 1 x left adjusting device pneumatically for electropneumatic lateral operation to manual 8-fold revolver per motor 1 x left chamfer/radius sanding aggregate top PS 42 1 motor 0,55 KW height adjustment with the top pressure workpiece thickness 12 - 60 mm Radius max. 12 mm sanding belt length 2000 mm, width 20 - 35 mm belt speed 7 m/sec. sanding pressure manually adjustable without sanding shoe 1 left adjusting device pneumatically for electropneumatic lateral operation to manual 8-fold revolver per motor 1 x left cleaning agent application top/bottom 1 x left EDGE BUFFING UNIT TOP + BOTTOM with oscillation for smoothing-off the edges 2 motors each 0,25 kW adjustable in inclination and height height adjustment with top pressure oscillation device in order to exploit the com- plete disk width, for top and bottom motor. 1 x left work piece support for single-sided machines Change: extended extraction of workpiece support approx. 1200 mm 1 SPS control System HOMATIC 2000 with LED display allowed environment temperature min. + 5 degrees max. + 35 degrees celsius 1 input NC 20 1 control cabinet approx. 3600 x 600 x 2000 mm **************************************** the transformer 300 cy. is missing **************************************** air connection 1 x 1 , 6 bar, 1 x 1/2 , 6 bar connected load approx. 91 ADimensiones: 13600 x 2400 x 2100 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:41 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
scm
Modelo
OLIMPIC SE 215 ERL
País
España
Año
2004
Descripción
Número de serie AH/108746 Composición: · Grupo de encolado con cola termofusible y 3 rodillos de presión · Grupo retestador · Grupo perfilador recto · Grupo perfilador con motores inclinables · Grupo de formas · Grupo rasca-cola · Grupo de cepillado con 2 motores · Grupo Phon con calentador Leister Normativa CEDimensiones: 7500 x 2400 x 2200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 27/10/2020 10:02 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
hebrock
Modelo
KDP 106 A2
País
Alemania
Año
1996
Descripción
HEBROCK KDP 10 Edgebander tabletop unit for hot-melt adhesive prelaminated edges with electrical cutting station motor driven pressure roller infinitely electrically operated temperature control connection 230 volts, 50 cyc, approx. 3.1 kWDimensiones: 700 x 550 x 600 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:10 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KFL 23/06
País
Alemania
Año
1999
Descripción
HOMAG KFL 23/06 Squaring- and Edgebanding Machine fixed stop side on the left, movable side on the right basic machine: - with continuous machine frame and unit beam, prepared for installation of the panel sizing, edge banding and postprocessing units - incl. basic length noise protection for panel sizing and postprocessing part with central suction. workpiece transport device: - with precise, hardened running and guiding surfaces - magnetic motor braking of the transport chain top pressure: - with driven compound V-belt - motorized height adjustment via cardan drivewith digital position read-out width adjustment of the movable side: - motorized rapid/slow gear drive - digital position read-out lacquering: - structure lacquer grey RDS 240 80 05 electric equipment: - operating voltage 380 volt, 50 cyc. - control voltage 220 volt, 50 cyc. - installed according to European Norm EN 60204 - hand switch for setting operation - all 100 cyc. motors are operated with dynamical frequency converter and are equipped with electronic motor brakes - separate frequency converter - separate switch cabinet - connection cable to the machine according to the installation plan safety and protection facilities: - all machines destined for EC member countries are fitted with CE plates in accordance with EC Machine Directive 89/392/EEC Appendix IIA - wood dust protection max. 2 mg/m3, subjectto the required extraction capacity being provided by the customer according to the suction plan - documentation technical data: - feed infinitely variable 10 - 40 m/min. - workpiece overhang80 mm - workpiece thickness30 - 70 mm - working height up to upper chain 950 mm - working width double-sided min.240 - 270 mm(depending on machine equipment) - working width double-sided max. 2500 mm - the technical data for the basic machine may vary due to the processing units. - floor conditions have to correspond to the foundation plan changing: - top pressure shortened by 2 gradations 1 x left infeed fence doors line for workpieces with top layer overhang - fence approx. 2500 mm long - mounted at 2 guides 1 x left, 1 x right panel taking-over device for workpiece fixation, with chain infeed and lifting device, electropneumatic controlled max. workpiece length before cams 1300 mm 1 x right alignment station straight components with two units arranged on top of each other for positioning of doors 1 x right alignment station inclined components with two units arranged on top of each other for positioning of doors 1 x left lifting device with felt coating two lifting rails with felt coating - electronpneumatic controlled - felt coating approx. 30 mm wide 32 x left, 32 x right conveyor chain, rolling with ball bearings at running and guiding surfaces width of chain plates 70 mm 1 x left, 1 x right steplessly adjsutable stop cams manual cam projection max. 25 mm, manually adjustable to max. 4 different heights electropneumatic control for driving-out cams, preselection of cam distance 32 x left, 32 x right stepless stop cams cam projection max. 25 mm per cam 1 x left, 1 x right cams blowing-off device with suction hood 1 pressure control device 1 x left panel support in reinforced construction Note: - righthand machine side 1 x right prescoring unit 2,2 kW controlled 1 motor 2,2 kW, 100 cyc. 6000 rpm. with lifting device assembly at hogging motor for tool diameter max. 180 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection 1 x right hogging unit 11 kW 1 motor 11 kW, 100 cyc., 6000 rpm. mounting surface for scoring motor cross support, double suction hood swivelling by 15 degrees in case of panel overhang = 60 mm. star-delta connection tool diameter max. 250 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection 1 x right motor shaft D = 40 mm for mounting of hydro clamping special motor shaft dimension without standard key motor shaft length 75 mm, hardened 1 x right trimming column 2 guides 1 x right standard trimming unit pneumatic control 6,6 kW 1 trimming motor 6,6 kW, 100 cyc. 6000 rpm. cross support,pole-changing switch for direction of rotation, suction hood, intermediate support with round guide, electropneumatic control for intermittent trimming, swivelling range 90 degrees tool diameter max. 200 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection Note: opposite movement for coldness sealing 1 x right standard trimming unit pneumatic control 6,6 kW 1 trimming motor 6,6 kW, 100 cyc. 6000 rpm. cross support,pole-changing switch for direction of rotation, suction hood, intermediate support with round guide, electropneumatic control for intermittent trimming, swivelling range 90 degrees tool diameter max. 200 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection Note: synchronous movement for coldness sealing 1 x right trimming column 1 guide 1 x right trimming unit top and bottom 1 kW 2 motors each 1 kW, 300 cyc., 18000 rpm. with plug-type connection manual lateral movement height adjustment with the top pressure working in opposite movement spindle adjustment for lateral tracer roller edge thickness max.20 mm workpiece thickness max. 60 mm swivelling range 0 - 25 degrees without tools incl. electronic frequency invertor with motor braking function and extension noise protection Note: for chamfer in synchronous movement 1 x left separating agent spray spreading top 1 x left prescoring unit 2,2 kW controlled 1 motor 2,2 kW, 100 cyc. 6000 rpm. with lifting device assembly at hogging motor for tool diameter max. 180 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection 1 x left hogging unit 11 kW 1 motor 11 kW, 100 cyc., 6000 rpm. mounting surface for scoring motor cross support, double suction hood swivelling by 15 degrees in case of panel overhang = 60 mm star-delta connection tool diameter max. 250 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection 1 x left motor shaft D = 40 mm for mounting of hydro clamping special motor shaft dimension without standard key motor shaft length 75 mm, hardened 1 x left trimming column 2 guides 1 x left standard trimming unit pneumatic control 8,1 kW 1 trimming motor 8,1 kW, 100 cyc. 6000 rpm. cross support,pole-changing switch for direction of rotation, suction hood, intermediate support with round guide, electropneumatic control for intermittent trimming, swivelling range 90 degrees tool diameter max. 200 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection changing: 1. lift in intermediate support 50 mm instead of 25 mm 2. blowing-off of stop 3. for scoring of bottom and rebate finish trimmingof rear edge 1 x left motor shaft D = 40 mm for mounting of hydro clamping special motor shaft dimension without standard key motor shaft length 75 mm, hardened 1 x left adjustment manual to counter for stop in intermediate support, in or to stop the motor in rebate height 1 x left star delta start-up 1 x left hogging unit 11 kW 1 motor 11 kW, 100 cyc., 6000 rpm. mounting surface for scoring motor cross support, double suction hood swivelling by 15 degrees in case of panel overhang = 60 mm. star-delta connection tool diameter max. 250 mm without tools incl. electronic frequency invertor with motorbraking function, extension of noise protection Note: for rebate finish trimming in opposite movement 1 x left motor shaft D = 40 mm for mounting of hydro clamping special motor shaft dimension without standard key motor shaft length 75 mm, hardened. 1 x left trimming column 1 guide 1 x left prescoring and smoothing unit top 1 motor 1 KW, 300 cyc., 18000 rpm. height adjustment with top pressure working in synchronous movement tracing from top and lateral spindle adjustment for motor and tracing without tooling diamond tools recommended. incl. extension noise protection and motor braking function 1 x left adjusting device trimming motor automatic 8-fold for electropneumatic movement on automatic 8-fold turret, for different edge thickness or profile depths separate motor connection 1 x left adjusting device tracing roller automatic 8-fold for electropneumatic movement on automatic 8-fold turret, for different edge thickness or profile depths. Separate motor connection. 1 x left console for panel sizing part for installation of an individual unit 1 x left compact alternating trimmng unit 2 x 6,6 kW 2 motors each 6,6 kW, 100 cyc. 6000 rpm. cross support,electropneumatic control for both motors, operating stroke max. 15 mm, swivelling range 90 degrees, manually adjustable via spindle, suction hood for both motors tool diameter max. 180 mm without tools incl. motor braking and extension of noise protection Note: for impact and cornice profile, set tool is used 1 x left trimming column 2 guides 1 x left standard trimming unit pneumatic 1,5 kW, 45 degrees 1 trimming motor 1,5 kW, 100 cyc. 6000 rpm. cross support,pole-changing switch f. direction of rotation, suction hood, intermediate support with round guide, electropneumatic control for intermittent trimming, motor inclined by 45 degrees, with bottom hanging motor shaft lift max. 50 mm blowing-off of stop tool diameter max. 200 mm without tools incl. motor braking function and extension of noise protection Note: for chamfer at impact 1 x left unit beam 500 mm long for installation of processing units installed on a fixed panel overhang 3 x left extension unit beam by 100 mm each 1 x left lateral adjustment of unit beam manual for manual adjustment of workpiece overhang within the range of 40 - 110 mm 1 x left trimming unit soft top 1 kW controlled 1 motor 1 kW, 300 cyc., 18000 rpm. with plug-type connection electropneumatically controlled inclined by 20 degrees, manual lateral movement height adjustment with the top pressure lateral adjustment for tracer roller on manual 8-fold turret for radii max. R 12 mm without tooling incl. electronic frequency invertor with motor braking function and extension noise protection Note: 1. in synchronous movement 1 x left unit beam 500 long for installation of processing units installed on a fixed panel overhang 10 x left extension unit beam by 100 mm each 1 x left lateral adjustment of unit beam manual for manual adjustment of workpiece overhang within the range of 40 - 110 mm 1 x left height adjustment of unit bam stepless positioning via stepless axis adjusting way -30 mm to bottom +30 mm to top 1 x left hot melt gluing unit QE 34 melting unit with container for granulates melting capacity depending on glue max. 18 - 35 kg/h. electronic temperature adjustment with LED-read-out glue rollerdiameter 34 mm glue roller heated level control of melting quantity 1 x left electric time relay for glue container, with power reserve 1 x left QE 34-front part extended to edge height 85 mm instead of 65 mm 1 x left additional kit for hot melt softforming/E glue application to edge material or workpiece electropneumatically controlled cooling nozzle at the end of the pressure zone blowing nozzle for workpiece cleaning 1 x left magazine HL 11 - 6 rolls 1,0 mm edge thickness0,4 - 1 mm edge width 16 -45 mm processing 45 mm2 roll diameter max.600 mm number of rolls 6 - detached magazine clipping unit roll change 3 x 2 rolls automatically or 6 x 1 roll manually, edge control with feed stop remnant edge length control in case of 2000 mm edge control with feed stop 1 x left remnant edge legnth control magazine HL 10/11 stepless adjustment of residual length between min. 2400 mm and max. 3100 mm Note: for max. length 1300 mm 1 x left edge width 65 mm for magazine HL 11 - 6 rolls instead of 45 mm, workpiece thickness max. 60 mm 1 x left pressure zone C 3 post-pressure roller dia. 150 1 driven pre-pressure roller diameter 200 mm pneumatic pressure adjustment, for straight edges centralized adjustment for change-over in case of different edge thicknesses changing: 1. 2 post-pressure rollers manually lateral adjustable 2. pre- and post pressure rollers hard-chromed 3. first post pressure roller driven via O-ring 1 x left unit beam 500 mm long for installation of processing units installed on a fixed panel overhang 1 x left extension unit beam by 100 mm each 1 x left height adjustment of unit bam stepless positioning via stepless axis adjusting way -30 mm to bottom +30 mm to top 1 x left edge activation decorative side 12 kW for heating the edge with hot air temperature adjustment and reversing flap for hot air installed between 1st pressure roller and profile pressure track to be connected via tracer in the control panel 1 x left pressure zone for rebate gluing complete on length SM 1 hot-melt glue reactivation device 15 kW 1 rebate pressure zone with bending rod 1 pressure roller set for rebate vertical adjustment manual via spindel and digital counter 1 panel pre-heating 2 heater 1 x left profile pressure roller set G fixed at top pressure electropneumatic movement out of working area to be used for U-profiles with different workpiece thicknesses 1 x left snipping unit HL 04 chamfer/straight 2 motors each 0,23 kW, 300 cyc., 18000 rpm edge thicknessstraightmax. 6 mm chamfer max. 3 mm edge widthmax.65 mm edge cross sectionmax. 270 mm2 automatic central lubrication of the linear guide 2 special TCT snipping saws diameter 120 mm incl. electronic frequency invertor with motor braking function and extension noise protection changing: 1. mounted for 18 mm snipping depth 2. only for straight edges 3. max. door thickness 70 mn, straight edge 4. with waste chute 5. mounted on 220 mm height 6. with second, double saw blade for impact chamfer 1 x left unit beam 500 mm long for installation of processing units installed on a fixed panel overhang 28 x left, 28 x right extension unit beam by 100 mm each 1 x left lateral adjustment of unit beam manual for manual adjustment of workpiece overhang within the range of 40 - 110 mm 1 x left trimming unit soft top 1,5 kW controlled 1 motor 1,5 kW, 300 cyc., 18000 rpm. electropneumatically controlled inclined by 20 degrees, manual lateral movement height adjustment with the top pressure lateral adjustment of tracer roller on manual 8-fold turret for radii max. R 12 mm without tooling Note: ----- in opposite movement 1 x left pneumatic adjusting device for trimming motor for electropneumatic lateral movement out of the processing area Separate motor connection. 1 x left trimming unit soft top/bottom 1,5 kW 2 motors each 1,5 kW, 300 cyc., 18000 rpm. inclined by 20 degrees manual lateral movement, height adjustment with the top pressure separate motor connection lateral adjustment of tracer roller on manual 8-fold turret for radii max. R 12 mm without tooling Note: ----- in opposite movement 2 x left pneumatic adjusting device for trimming motor for electropneumatic lateral movement out of the processing area separate motor connection. Note: ----- The existing snipping unit WK47 as well as the buffing unit top/bottom are not applicable. 1 x left corner rabete snipping unit WK 26 leading edge 1 motor 0,23 kW, 300 cyc., 18000 rpm workpiece thickness max. 65 mm edge thicknessmax.1 mm rebate height max. 30 mm rebate snipping depth max. 15 mm 1 TCT-special snipping sawdiam. 80 mm, t=30 automatic central lubrication of the linear guide incl. electronic frequency invertor with motor braking function and extension noise protection 1 x left corner rabete snipping unit WK 26 trailing edge 1 motor 0,23 kW, 200 cyc., 18000 rpm workpiece thickness max. 65 mm edge thicknessmax.1 mm rebate height max. 30 mm rebate snipping depth max. 15 mm 1 TCT-special snipping sawdiam. 80 mm, t=30 automatic central lubrication of the linear guide incl. electronic frequency invertor with motor braking function and extension noise protection 1 x left panel blowing-off device Note: top 1 x left noise protection door itnerlocking according to BG-prescriptions, necessary for finishing part Functioning: In case machine runs with open noise pro- tection doors, there will be an acoustic signal after four minutes, doors have to be closed now within a further minute, otherwise feed will stop. 1 x left unit beam 500 mm for installation of processing units installed on a fixed panel overhang 10 x left extension unit beam by 100 mm each 1 x left lateral adjustment of unit beam manual for manual adjustment of workpiece overhang within the range of 40 - 110 mm 1 x left height adjustment of unit bam stepless positioning via stepless axis adjusting way -30 mm to bottom +30 mm to top transfer finish foiling unit 3 rollers for application of a decorative stamping foil onto a suitable base material, e.g. MDF. Consisting of: preheating station with infrared radiators for heating the panel edge before hot stamping hot-stamping unit with 3 stamping rollers, basic diameter 200 mm, to be individually positioned by pneumatic cylinder electronic temperature control for each stamping roller foil rewinding by adjustable rotary-field magnet Disk diameter 300 mm Feed,depending on profile/foil: max. 15m/min. Profile unrolling:max. 50 mm Profile depth:max. 10 mm changing: --------- without preheating station space requirement: 1700 mm rebuilding set for stamping station Note: ----- rebuilding set for installation of stamping station onto unit beam 1 x left frequency changer 35 KVA 100 cyc, IP 54 for scoring / hogging left + right 1 x left frequency changer 70 KVA 100 cyc, IP 54 for the other motors 1 x left frequency changer 15 KVA 300 cyc, IP 54 1 Homatic electronic control programmable memory control (PLC) system 'HOMATIC 2000' with indication of all inputs and outputs by means of luminous diodes Integrated line control for remote control of processing units. - multi-tasking control of PLC for precise unit operation - free number of workpieces in the machine - compatible interface to all Homatic-inputsystems permissible environmental temperature min. + 5 degrees Cels., max. + 35 degrees Cels. 4 x right extension Homatic electronic control per step 29 x left extension Homatic electronic control per step 1 x right electronic width adjustment EB 02 with rapid - and slow gear change-over positioning in a loop drive adjustment speed: rapid gear=2,2m/min. slowgear= 25 mm/min. 1 x left, 1 x right electronic height adjustment 1 feed interlocking for Homag machines 1 air conditioning for switch cabinet will be necessary if the environmental temperature at the machine is higher than 35 degrees C or machines with servo-drives and frequency-adjusted drives. Only suitable in case of separate switch cabinet. 1 x left input NC 21 HOMATIC control system with graphic surface for an easy and comfortable operation and programming of a Homag machine. Hardware: - industrial computer 68040 with 16 MByte RAM - 1 PCMCIA fixed-disk 170 MByte - 1 free PCMCIA insert for data securing - colour display 12,1 inch with PC compatible keyboard integrated in operation desk at the infeed - expandable with network connection Ethernet Software: - real-time operation system OS9 with Windows surface - operation with Windows standard via selection menu - menu conducted creation of operation programs - production according to operation programs - contact plan diagnostic PLC on the display Remote diagnostic: - telephone modem on a loan until the machine acceptance at the customer's work, return or taking over according to separate diagnostic contract - 2 telephone lines are to be installed up to the machine by the customer, one of these 2 lines should include a telephone 1 machine and up to 2 additional transport devices in 1 line can be controlled by the HOMATIC control. Required for all machines with stepless axes. Attention!!! A transport frame from HOMAG is required for transporting the dismantled machine, for which costs of EUR 2000,- plus VAT will be charged. After return of the transport rack to SURPLEX, the amount will be refunded minus a value reduction of 10 %. The return costs to our warehouse must be paid by the customer. The return address is as follows: Surplex Warehouse Im Hasseldamm 1 41352 Korschenbroich Germany The return must be pre advised one week before delivery. Dimensiones: 39000 x 2500 x 2400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 11:32 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
FKR 79/05/QA
País
Alemania
Año
1992
Descripción
work-piece width min. 85 mm height of work piece min-max 7-60 mm edge thickness min. max. 1,4-14 mm feed 10-30 m/min. feed speed infinitely variable work-piece overhang 40 mm stop side right jointing-/profile-trimming 1 glue indication glue roller gluing aggregate hot melt glue edge magazin roller 0,4-3,5 mm edge magazin strips edge magazin massive 14 pressure zone straight snipping chamfer-straight flush milling 1 chamfer / radius milling 2 profile trimming / copying (4 motors) 1 universal trimming unit 2 profile sliding blade bottom 1 flat sliding blade top/bottom 1 buffing aggregate top/bottom 1 height adjustment powered electronic control The loading dimensions have been roughly recorded. If you have a transport request, we must first request it from the seller.Dimensiones: 26000 x 2450 x 2500 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:20 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
holz-her
Modelo
1438 Express
País
Alemania
Año
1992
Descripción
HOLZ HER 1438 Express EdgebanderDimensiones: 1200 x 1700 x 5100 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 22/10/2020 11:06 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
O KDF 650 C
País
Alemania
Año
2007
Descripción
Adjustable infeed ruler Release agent spray device Pre-milling unit, Glueing unit, Flush milling, End trimming unit, rounding (1 and 2 mm), Corner copying, Radius scraper Surface scraper buffing Cleaning agent spraying device total working hours: 2656.54 h, edge length: 186535.8 mDimensiones: 5300x1200x1800 mmEstado: funcionandoCondiciones de entrega: cargado en camiónFinal de la subasta: 22/10/2020 10:04 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
emme elle
Modelo
T.I. 800
País
España
Año
1997
Descripción
• Cizalla, guillotina • Número de serie 9705 • Máxima longitud de corte aprox. 800 mm • Máxima altura de corte aprox. 60 mm • Bomba hidráulica con motor 3 KW•1425 rpmDimensiones: 1850 x 600 x 1350 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 28/10/2020 13:37 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
emme elle
Modelo
País
España
Año
Descripción
• Cizalla, guillotina • Máxima longitud de corte aprox. 800 mm • Máxima altura de corte aprox. 50 mm • Bomba hidráulica con motor 3 KW•1415 rpmDimensiones: 1300 x 1200 x 1350 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 28/10/2020 13:36 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
emme elle
Modelo
TO 2800
País
España
Año
2000
Descripción
• Cizalla, guillotina • Número de serie 2017 • Máxima longitud de corte aprox. 2800 mm • Máxima altura de corte aprox. 90 mm • Bomba hidráulica con motor 5.50 KW • Con alimentador de chapaDimensiones: 3750 x 1950 x 1730 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 28/10/2020 10:49 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
panhans
Modelo
923
País
Austria
Año
Descripción
Edge banding press with 2.5 mm, hydraulicDimensiones: 2800 x 700 x 1200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:27 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
holz-her
Modelo
1401
País
Austria
Año
Descripción
Edge banding and flush milling up to 20 mm solid, cartridge system, 2.600 mm lengthDimensiones: 2700 x 900 x 1400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:36 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
KD 84
País
Austria
Año
1994
Descripción
up to 12 mm, Gluing, capping, flush milling, rounding, 2 x free spacesDimensiones: 5500 x 1000 x 1850 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:35 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
holz-her
Modelo
1410
País
Austria
Año
Descripción
Gluing, capping, flush milling, cartridge system, up to 25 mm solid edgesDimensiones: 5000 x 900 x 1400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:23 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KR-74
País
Austria
Año
Descripción
Gluing, capping, flush milling, rounding milling, buffing unitDimensiones: 6500 x 1200 x 1700 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:22 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
olimpic
Modelo
MOB 1
País
Austria
Año
Descripción
Edge banding and millingDimensiones: 3300 x 1000 x 1500 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 11:14 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
ima
Modelo
Advantage 700
País
Alemania
Año
2008
Descripción
IMA Advantage 700 Edgebander for edges up to 3 mm(1/8 ) and solid wood lippings up to 12 mm(1/2 ) • Top pressure beam with compound V -belt an electronic height adjustment • Icos TS operator panel - 12 touch-screen with graphical operator guidiance - programm memory for 1000 processing programs - error display in clear text • infeed fence wth NC adjustment • Anti-stick agent applicator for careful removal of glue residues • Calibrating unit 2x 3,0 kW • Glueing unit with IMA quick-lock-system for the quick change of the glue applicator • Pneumatic pressure zone with one driven main pressure roller and 5 additional rollers - adjustment via NC axis • End trimming unit 2 x 660 W; 200 Hz - pneumatic adjustment of end-trim and chamfer cut(8°) via control panel • Milling unit 2 x 1000 W ; 200 Hzwith HSK 25 tool receptacle - Special vertical tracing for panels with boreholes • MFA multi function unit 08.342 - fine milling of upper and lower edges as well as contour trimming of leading and trailing edges - all movements of the unit are accomplished via servo-drives - infinite NC controlled positioning for different edge thickness • Profile scraper • Flat scraper • Cleaning agent applicator • Buffing unit Dimensiones: 9000 x 1700 x 1900 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 22/10/2020 10:51 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
holz-her
Modelo
1421
País
Austria
Año
1991
Descripción
Edge banding/milling, solid wood up to 20 mm, nozzle applicationDimensiones: 3150 x 800 x 1400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 10:59 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
holz-her
Modelo
1408
País
Austria
Año
1988
Descripción
Edge banding/trimming/milling, solid wood up to 20 mm, nozzle applicationDimensiones: 4400 x 900 x 1400 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 10:53 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
KL-31
País
Austria
Año
Descripción
Gluing, capping, millingDimensiones: 4000 x 900 x 1150 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 10:33 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
ott
Modelo
País
Austria
Año
Descripción
Paper Veneer Gluing MachineDimensiones: 1450 x 800 x 1200 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 09/11/2020 10:42 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
brandt
Modelo
OKD 79/2 CF
País
Reino Unido
Año
2003
Descripción
Machine number 0-261-02-8912, 400 V, 50 Hz, 15.6 kW, Quickmelt gluing aggragat, jointing trimming unit, gluing unit, trimming unit, flush trimming unit, rounding trimming unit, corner copying unit, scraper and buffing unit, display replaced by addi, tional monitorDimensiones: 6500 x 1300 x 1900 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 23/10/2020 14:13 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
biesse
Modelo
ROXYL 5.5
País
Reino Unido
Año
2013
Descripción
Machine number 94391, 7 bar, 30 m/s, jointing trimming unit, gluing unit, trimming unit, multifunction trimming unit, scraper, profile trimming unit and buffing unitDimensiones: 7000 x 1400 x 2100 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 23/10/2020 14:10 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

chapeadora {{favorit}}

Marca
cehisa
Modelo
ep-7
País
España
Año
Descripción
chapeadora cehisa, mod. ep-7, con grupo encolador, retestador y perfilador superior e inferior para recto y radio. maquina ce a 380 v.muy buen estado.
EUR

Marca
brandt
Modelo
KDF 660 C
País
Alemania
Año
2005
Descripción
Edge banding machine KDF 660 Single sided edge banding machine in right hand guide for hot-melt gluing. Quick-change gluing unit for hot-melt glue. Processing of PU-glue granulate under Observe the adhesive processing instructions possible. Glue supply leak-proof under the glue roll. Fine dosage of glue to the workpiece by means of glue roll, no adjustment to factory piece thickness required. Glue roll direction of rotation either constant or Reverse course. Glue temperature monitoring by means of electronic thermostat. Automatic glue temperature reduction at Work stoppages. Infrared hot melt activation. Automatic edge magazine for roll goods and Fixed lengths, incl. roller plate diameter 800 mm. Equipment with reinforced pre-cutting shears for Thick PVC/ABS max. 3 x 45 mm. Standard equipment with edge- and work- piece distance monitoring by means of optical Display. Heavy pressure zone with driven, pneumatic table loaded main pressure roller and 3 free-running holding rollers. Standard equipment with automatic Central lubrication for the transport chain. Central adjustable upper pressure. Control panel at machine infeed. Electronic control PC 16 ------------------------- BRANDT control system with color graphics- User interface for easy and intuitive comfortable operation and programming. Technical details: - Swivelling control panel at the machine infeed - Durable short-stroke membrane keyboard - Colour graphics flat screen - Industrial PC with compact flash disk as Mass storage - Genset function keys with LED status display - Support of the operator guidance by colour- Pictograms - Online language switching between various Foreign languages - Representation of the essential machine setpoints and actual conditions - Status messages in plain text - Easy selection and correction of the route points - Simple possibility of axis adjustment (with corresponding aggregate design) - Online help in plain text by any time accessible help window - Production data acquisition for production time edge length and number of workpieces, as daily and total value - Inspection and maintenance interval display - Remote service possibility through integrated Modem and installed service software - Saving of machining programs - Production according to machining programs - Data backup of machining programs on diskette Electrical equipment with modular Control system for increased operator comfort. Modem for remote service and remote maintenance of machine via the public telephone network. For this purpose, an analog Telephone connection required on the machine. Noise protection cladding including central suction connection diam. 120 mm and chip trap box for scraper shavings with suction socket Diameter 100 mm. For machines with a Joining milling unit (KDF machines) additional Suction connection Diameter 120 mm. Permissible ambient temperature min. +5 degrees/ max. +35 degrees Celsius, for electrical and mechanical functioning of the machine. The processing guidelines of the glue and Edge manufacturers must be observed. For mains voltage fluctuations greater than +/- 10 a voltage stabilizer must be installed at the place of use can be installed. Machine deliveries for EU countries safety- technically executed in accordance with EC directive 98/37/EC, Annex I. Technical data edge thickness 0.4 - 12 mm Roll separation max. 3 x 45 mm or 0.8 x 65 mm workpiece thickness 8 - 60 mm Feed rate max. (*) approx. 14 m/min (*) When selecting the form milling machine automatic switchover to 11 m/min. electrical 400 V - 3 Ph. - 50 Hz Pneumatic connection min. 6 bar Connected load approx. 12 kW QUICKMELT - GLUED PART Pre-registrator and quick change- bar, small volume gluing unit instead of the standard gluing unit. JOINT MILLING UNIT 2 X 2,2 KW 200 HZ FG 3500 For joining before the gluing part, spindle gluing vertical position, electro-pneumatic Control horizontal, 2 motors (1 x equal-, 1 x counter rotation), max. chip removal / stroke 3 mm (The maximum chipping cross section depends on of material and feed speed) Covering hood with suction socket diam. 120 mm. Equipment without joining tools SET OF JOINTING CUTTERS 48 MM DIA for use on jointing and milling unit. 2 permanently mounted DIA joining heads diam. 100 x 48 x diam. 30 mm, Z = 3 + 3 with double keyway 8 x 3 mm max. workpiece thickness 42 mm CROSS-CUT UNIT CHAMFER/STRAIGHT 2 X 0,35 KW For cutting the front and rear edge of the projection with pulling cut for high accuracy. Edge dimensions: max. 12 x 40 mm max. 3 x 65 mm 2 motors each 0.35 kW, 200 Hz, 12,000 rpm swivel range straight on chamfer caps 0-15 degrees Equipped with 2 crosscut saws diam. 100x32x2,6 mm Z = 30 Feed speed: max. 14 m/min. PNEUMATIC ADJUSTMENT CAPS CHAMFER/STRAIGHT For the electro-pneumatic changeover of the crosscut aggregates from chamfer to straight. MILLING AGGREGATE 2 X 0,55 KW 0 - 25 DEGREES COUNTER DIRECTION For flush milling of the upper and lower Edge material overhang. 2 motors side-by-side. arranged one above the other, vertically and horizontally tentative, manually moveable 30 mm sideways. Height adjustment of the upper motor with the Positive pressure. Digital counters for quick adjustment. Spindle adjustment for lateral sensing rollers. edge thickness max. 15 mm workpiece thickness 8 - 60 mm Swivel range 0 - 25 degrees Standard equipment with 2 pcs. WPL cutters diam. 70 x 20 x 16 mm, Z = 4. PNEUMATIC ADJUSTMENT OF MILLING UNIT For electro-pneumatic axial movement of milling units on manual 4-fold Revolver attacks. Aggregate individual adjustment top/bottom SHAPING MILLING UNIT TOP+BOTTOM 2 X 0,35 KW FF 6220 For form/flush milling of head edges on post- and softforming parts and corner rounding of Thick PVC edges. Wooden edges are possible to a limited extent, depending on preliminary tests. Optionally radius- or chamfer milling cutters can be mounted. Restrictions for loose center layers on Post-/Softforming parts and extremely thin Melamine/foil edges and surface mate- rialien. 2 motors each 0.35 kW, 200 Hz, 12000 1/min. edge thickness max. 3 mm (radius) workpiece thickness max. 55 mm Feed speed max. 11 m/min. Including pneumatic 2-point- Adjustment chamfer/radius. Delivery without milling tools Suitable for the following milling tools: VKNR 4873 - WPL radius cutter set VKNR 4827 - WPL chamfer milling cutter 15 degrees (2 x) WPL-RADIUS MILLING CUTTER SET FORM MILLING 2 WPL radius cutters Diameter 58/50 x 12 x 16 mm, Z = 4 for radii r = 2 mm SCRAPER WITH QUICK CHANGE HEADS ZK 6510 Scanning from above, below and sideways. To Chamfering or rounding of pre-milled PVC edges. Max. edge thickness 3 mm. Height adjustment of the upper device with the upper pressure, including 2 quick-change heads for simple radius change, with 2 WPL profile knives r = 2 mm. PNEUMATIC ADJUSTMENT SCRAPER 5760/5736 for electro-pneumatic lateral movement of the scraper units 1 set, 2 quick change heads for profile scraper additionally BUFFING UNIT 2 MOTORS FP 6810 For getting a grip on the edges at the top and bottom. 2 motors each 0.18 kW, individually suspended, adjustable in height and inclination. Height adjustment of the upper motor with the Positive pressure. 2 molleton discs diam. 150 x 20 mmDimensiones: 7000 x 1700 x 1900 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónFinal de la subasta: 20/10/2020 10:00 MEZEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
elwood
Modelo
ATHENA B 10
País
España
Año
2005
Descripción
Número de serie 2200, Potencia total instalada 10.50 kw, Control, Bandeja para 1 rollo de canto, Grupo de cola, Grupo de presión con 1+3 rodillos, Retestador, Grupo de radios, Grupo de rascadores, Grupo de cepillos de pulidoDimensiones: 3950 x 1300 x 1700 mmEstado: sin comprobarCondiciones de entrega: cargado en camiónEste artículo se vende exclusivamente por medio de un mecanismo de subasta en anuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
homag
Modelo
POWER LINE KFR 24/27/29/QA/30
País
Italia
Año
2006
Descripción
FLEX LINE (half line) POWERLINE of Double-side Sizing-Milling a) Double Loader BARGSTEDT (28 cycles/min) TBH 510/D/30/12/S b) Infeeding rollerway, with Turning device HOMAG TD 31/30/12 with double cone c) FLEXIBLE Double-side Sizing right sizing Glueing Area (Quick Melt unit, Glue Pot, No. 24 Edge Coils supports), Snippping unit, Overlapped Trimmers, Multi function Unit FK 23 (fine-trimming and corner rounding process, with automatic tool changing system), N. 1 Milling Grooving unit by N.C with automatic tool changing system, N. 1 Milling unit by N.C., Edge Scraper unit by N.C. (with Multi-profil knife), Glue scraper, Buffing Unit, Free space d) Outfeeding Rollerway with Turning device HOMAG TD 51/30/12 with double cone e) Double Unloader BARGSTEDT (28 cycles/min) TBH 510/D/30/12/S Dimensiones: 216000 x 2400 x 2550 mmEstado: buenoCondiciones de entrega: cargado en camiónanuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Marca
biesse
Modelo
Akron 1440-A
País
Alemania
Año
2018
Descripción
BIESSE Akron 1440-A edge banding machine Exhibition machine / subject to prior sale ATTENTION Pictures may show accessories not included incl. - jointing and milling unit RT02 - Scraper unit RB02 - Surface scraper RC02 - Buffing unit SZ02 - Smart Touch 21.5 control - NC Axis Package - Feed speed 12-18 m/min - Installation preparation for plate return - Spraying device for non-stick agent ADZ02 - Kit Pair of diamond cutters H=65 mm Z=2+2 30 - Kit Pro-Glue - Edge conveyor roller with short needles - Electrical and mechanical preparation for double gluing system - Quickmelt QM-703 for EVA hot melt - Adaptive Infra Red Lamp AdIRL-700 - Kit Pro-Nesting for fine milling unit - Pair of multi profile cutters for fine milling unit - Function for setting the machining only at the corners - Pair of milling cutters, R=2 mm, for form milling unit - Kit Pro-Nesting for scraper unit - pair of knives R=2 mm for scraper unit - Pair of knives R=1 mm for scraper unit - Cleaning unit LTP02 General product information Biesse Akron 1440-A edge banding machine Single sided edge banding machines for gluing and processing of flat edges in rolls (melamine, PVC, ABS, veneer) and strips (solid wood, resopal, sliced veneer, etc.) Standard equipment NC control with touch display The SMART TOUCH 10 NC control system enables simple and intuitive control of the machine and its individual units. Technical details: - Graphic colour display TFT 10 touch screen, 1024x768 pixels for a sharp and intuitive display of texts and images. - Windows operating system. - 4GB integrated hard disk for storing multimedia content and programs. - USB port for easy and effective management of multimedia content, programs and updates. - Ethernet port for connecting the machine to the network. - Sintra HD software, simple and intuitive touch screen interface, quickly learnable by any operator. Multilingual adjustable. Additional functions - Autostart of the selected genset motors. - Direct selection for second run. - Automatic management of NC axes and machining operations. - Program lists with manual and/or auto start. - Error diagnostics with comments. - Production data acquisition. - Software-guided maintenance. - Control panel ergonomically arranged and rotatable. Structure of the basic machine - Machine base: Highly rigid welded construction and contact surfaces milled in one clamping enables flexible and customer-specific assembly of the units. Machine bed open at the bottom allows free sliding - of the shavings to the outside. - Workpiece transport: Conveyor chain and top pressure as an integrated unit allow a safe and continuous holding of the workpiece during the passage. Conveyor chain: Heavy 1¼ inch (31.75 mm) industrial chain and technopolymer chain plates with self-lubricating properties. Special 80x60 mm rubber pads with high-grip provide a firm grip on the workpiece. Chain driven by a 1.5 kW motor gearbox unit. Top pressure: Steel frame construction with offset double row of rubber rollers with ball bearings. Automatic positioning of the top pressure beam which is controlled by the PLC. - Lateral sliding on ball guides. These are extruded aluminium guides complete with support wheels. Fast manual positioning of the locking system. Maximum work piece size: 40 kg; for larger panels a lateral panel guide is recommended. - Infeed ruler: Machines with joining unit are equipped with an adjustable infeed ruler. The adjustment is done manually or as an option automatically. Complete with workpiece separator at the infeed with special sensor in addition to the signal lamp to keep the space between the workpieces to a minimum. - Full protection cabin on the whole length of the machine except in the area of the grinding unit. It is made of aluminium with wide areas of transparent polycarbonate for a complete view of the operative units to ensure full incidence of light. Requirements for the electrical system The protection of the machine against indirect contacts has been designed for supply networks of type TN and consequently no residual current protection has been provided. In case of connection to other types of networks (TT, IT) or if required by local laws or standards, residual current protection must be planned according to the system characteristics. The following conditions must be observed: The measures against electromagnetic interference can generate high residual currents at high frequency. Technical data workpiece thickness* 10 - 60 mm edge height 14 - 64 mm Edge thickness of rolled goods 0.4 - 3 mm Edge thickness strip** 0.4 - 12 mm workpiece overhang 25 mm Minimum panel length 140 mm Minimum width (for 140 mm length) 85 mm Minimum width (for 250 mm length) 50 mm Feed speed 12 m/min workpiece gap** 650 mm Suction at each working unit 1 connection Ø 100 mm Compressed air supply 7 bar Mains voltage 400 V / 50 Hz Three phase with neutral Control voltage 24 V - CC Frequency of the static converter 200 Hz Glue tank capacity 2 (approx.) Kg Melting time with half filling 10 (approx.) minutes * Minimum workpiece thickness 8 mm with maximum edge thickness 1.5 mm. ** Depends on selected aggregates. According to EU directive. Free space for joint milling unit RT02 Gluing unit VC-511 Applies the hot melt adhesive to the workpiece, guides the edge to the workpiece, automatically cuts the edge off the roll and presses it against the workpiece, guaranteeing perfect positioning. It consists of: - Glue container and application roller. The application roller is equipped with a sliding shoe to get the right amount of glue on the workpiece. Hand lever for quick change of the gluing parts (NC controlled as option). No adjustment necessary if the panel thickness changes. Quick heating and double thermostat for differentiated temperature control. Glue tank completely coated with non-adhesive material. Electronic device for automatic temperature reduction of the gluing part when the machine was idle, for a defined period of time. Glue roller that rotates in the same direction as the board. Quick change of gluing parts for easy maintenance or changing colour/type of glue. - Automatic edge feeding system for edges in rolls or strips, complete with roll holder Disc diameter Ø 800 mm. The feeding of the edge is done by the infeed system when the panel moves forward and prevents the edge material from slipping off. The edge magazine has a manual vertical height adjustment. - Cutter knife for automatic cutting of edgebanding. Material in rolls with a maximum thickness of 3 mm and with a cross section of max 140 mm². Automatic adjustment of the working pressure according to the thickness of the edge banding on the first pressure roller. - Pressure rollers with RPT insertion-controlled pressure rollers, pressure device consisting of: o First pressure roller Ø100 mm with own air pressure regulator. o Two free-running pressure rollers Ø60 mm conical top, bottom. With non-stick coating and common air pressure regulator. Cross-cutting unit IN-801 Twin-engine cross-cut unit with one 0.8 kW each at 12000 rpm. For trimming the front and rear edge overhang with 0° to 15° inclination. Features: - High reliability and precision due to the slide shoes and prismatic guides. - Pneumatic changeover with preselection of the cutting angle between 0 and 15 degrees by means of PLC. - Exclusion of the cutting unit from the processing as well as an independently possible tilting of the two cross-cut motors. - Extraction system. - Flex system with controlled projection. Allows the saw blade cross-cut position to be adjusted from the control panel in order to obtain a certain protrusion of the edge. Ideal for applications that also require the shape milling function, especially for soft/postforming parts. Fine trimming unit RF02 Twin-engine milling unit, traced from above/below and at the front, each with 0.6 kW high-frequency motors and 12000 rpm. For processing the upper and lower edge overhang. Includes the pneumatic exclusion. Tools not included. 2 Motorised multifunctional shaping trimming unit AR02 E For corner rounding and form milling of workpiece edges made of synthetic material up to a maximum thickness of 3 mm. Complete with 2 high frequency motors with 12000 rpm each 0.65 kW. Corner rounding is possible for straight workpieces as well as on post- and softforming parts from 90 to 180 degrees. High production quality thanks to movement on linear guide, vertically oscillating copying device and a so-called pre-copying system. Maximum feed speed 15 m/min for corner copying. Tools not included. Free space for scraper unit RB02 Free space for surface scraper RC02 Free space for buffing unit SZ02 Free space for hot air unit PH-501 Joining and milling unit RT02 Joins the workpiece in process before the glue is applied. And two 1.8 kW high-frequency motors with 12000 rpm (without tools). The processing is splinter-free, precise and constant, thanks to: - Automatic, time interval controlled and independent switching on of the two motors. - The AUTO-SET device: ensures the optimal positioning of the cutters according to the thickness of the part to be machined. Symmetrical diamond tools H=45 mm Z=2+2 30° included. Scraper unit RB02 For finishing thick edges made of PVC/ABS. Complete with horizontal and vertical tracing rollers. Includes pneumatic exclusion. Standard with blowing nozzles on the tracing rollers and catch box for the chips. Tools not included. Surface scraper RC02 Unit for removing the leaked adhesive in the area where the edge joins the panel. Equipped with tracing rollers and a flat knife with insert control. The unit is equipped with a system for atomizing release agent to prevent it from sticking to the tools and a suction device. Buffing unit SZ02 For cleaning and buffing the workpiece edge with cloth polishing wheels. Complete with two 0.37 kW motors. 2800 rpm. The unit automatically adjusts to the thickness of the workpiece. Smart Touch 21.5 control Windows operating system, in: Italian, English, French, Spanish or German. - Colour touch screen 21.5 with Full HD resolution. - Port USB. Software features: - Windows operating system. - Interface for the control of edge banding machines. - Set-up operations for units and their axis settings (SMART TOUCH does not include axis control). - Program acquisition - and execution to automatically carry out the intended machining operations. - Automatic start of the unit and motor by means of a program. - Error diagnostics with code and plain text. - Detailed program lists. - Statistical data on production. - Automatic management of NC axes and machining operations. - Control system can be equipped. NC Axis Package - device for automation of action setting for Akron 1400 Complete with: - AX-1: Axis control with infeed ruler. - AX-1: Axis control on pressure rollers. - AX-4: Axis control on fine milling unit. - AX-2, axis controls on shaping milling unit. - AX-4, axis controls on scraper unit Feed speed 12-18 m/min The machine can have 2 different feed speeds: 12-18 m/min. Corner copying (form milling)/up and down machining: up to 18 m/min. Corner copying (form milling)/up and down machining: up to 18 m/min. Corner copying (form milling)/up and down machining: up to 18 m/min. Installation preparation for plate return Electrical preparation for connecting the return. The modified chain cover in the machine outlet is supplied loose. Spraying device for non-stick agent ADZ02 In order to achieve an optimal workpiece cleaning during the machining process, an anti-adhesive agent is sprayed on the upper and lower surface of the workpiece. The latter is positioned in front of the joint milling unit. Precise application of the anti-adhesive agent thanks to the injectors activated by numerical control. Kit Pair of diamond cutters H=65 mm Z=2+2 30°. As replacement for standard tools. Symmetrical tools. Kit Pro-Glue The PRO-GLUE kit consists of the following components: - TEKNO-GLUE system for optimal gluing through. Complete with: o Controlled scanning of the glue roll. o Automatic retraction in case of feed stop. o Automatic ON/OFF of the gluing part. - System REVERSE to switch the glue roller in synchronous or counter rotation Edge conveyor roller with short needles Exchangeable edge conveyor roller for better feeding of veneer edges. Electrical and mechanical preparation for double gluing system for the use of EVA glue in granule form and polyurethane glue in granule form. Quickmelt QM-703 for EVA hot melt Facilitates the change of colour/type of glue and fills the glue tank as required. The glue granulate is melted at 180°C and discharged directly into the glue basin. Consisting of: - Container for glue granulate with a capacity of approx. 3 kg. - melting device. - Glue container with filling level sensor, as a replacement for the standard glue container. Adaptive Infra Red Lamp AdIRL-700 The infrared lamp is placed in front of the gluing unit. Before the glue is applied, the workpiece is heated up to optimise the adhesion of the edge. High quality standard and minimizes operating costs. It is particularly useful for storing and/or processing boards in cold areas. Kit Pro-Nesting for fine milling unit Consisting of two pressure rollers with bearings as an addition from the UPPER vertical pressure roller to allow the machining of workpieces with holes with a maximum diameter of 35 mm and/or grooves. Distance between Pressure rollers 70 mm. Pair of multi profile milling cutters for fine milling unit Bevel milling 25 degrees, R=2 mm + R=1 mm and straight profile for solid wood. Function to adjust the processing only at the corners Pair of milling cutters, R=2 mm, for form milling unit Kit Pro-Nesting for scraper unit Consisting of two pressure rollers with bearings as an addition from the UPPER vertical pressure roller to allow the machining of workpieces with holes with a maximum diameter of 35 mm and/or grooves. Distance between pressure rollers 70 mm. Pair of blades R=2 mm for scraper unit Pair of knives R=1 mm for scraper unit Cleaning unit LTP02 Spray nozzles for applying cleaning agent to the plate directly in front of the buffing wheels for cleaning and polishing. The application is done by controlled nozzles. The warranty of this machine has expired! With the purchase of this machine you agree to this condition. The guarantee can be extended by Biesse at a charge. The costs amount to 2% of the list sales price for a further 6 months. This extension is always calculated from the end of the factory warranty!Dimensiones: 5700 x 1300 x 1800 mmEstado: no usado / nuevoCondiciones de entrega: cargado en camiónanuncio en web de Surplex (más información)anuncio en web de Surplex (más información) ... Leer más
EUR

Chapadora de cantos {{favorit}}

Marca
cehisa
Modelo
305
País
España
Año
Descripción
Encolar por calderín de cola termofusible. Tijeras para el corte del canto en rollo. Grupo de retestar. Grupo de refundir de desbaste. Grupo de refundir de acabado. Grupo rascador de radio. Grupo pulidor. Normativa CE
EUR

Chapadora de cantos {{favorit}}

Marca
holz - her
Modelo
1402
País
España
Año
Descripción
Encolar por cola de cartucho. Grupo de refundir. Grupo rascador. Grupo de formas/retestador. Grupo pulidor. Normativa CE
EUR

Categorías (epígrafes)

    Marcas

      Países

        Precio

        Años

        Seleccione los productos sobre los que desea información y pulse este botón