Referencias [1] Konter, M., Thurmann, M.: Materials and manufacturing of advanced industrial gas turbine com- ponents. J. Mater. Process. Tech. 117, 386-390 (2001) [2] Sidhu, R.K., Ojo, O.A., Chaturvedi, M.C.: Microstructural response of directionally solidified René 80 superalloy to gas-tungsten arc welding. Metall. Mater. Trans. A 40A, 150-162 (2009) [3] Henderson, M.B., Arrell, D., Heobel, M., Larsson, R., Marchant G.: Nickel-based superalloy wel- ding practices for industrial gas turbine applications. Sci. Technol. Weld. Joi. 9 (1), 13-21 (2004) [4] Liu, W., DuPont, J.N.: Effects of melt-pool geometry on crystal growth and microstructure develo- pment in laser surface-melted superalloy single crystals. Mathematical modeling of single-crystal growth in a melt pool (part I). Acta Mater. 52, 4833-4847 (2004) [5] Liang, Y.J., Wang, H.M.: Origin of stray-grain formation and epitaxy loss at substrate during laser surface remelting of single-crystal nickel-base superalloys. Mater. Design. 102, 297-302 (2016) [6] Bansal, R., Acharya, R., Gambone, J.J., Das, S.: Experimental and theoretical analysis of scanning laser epitaxy applied to nickel-based superalloys. Solid Freeform Fabrication proceedings 496-503 (2011) [7] Gaumann, M., Bezencon, C., Canalis, P., Kurz, W.: Single-crystal laser deposition of superalloys: processing-microstructure maps. Acta Mater. 49, 1051-1062 (2001) [8] Rottwinkel, B., Schweitzer, L., Noelke, C., Kaierle, S., Wesling, V.: Challenges for singlecrystal (SX) crack cladding. Phys. Procedia 56, 301-308 (2014) [9] Rottwinkel, B., Noelke, C., Kaierle, S., Wesling, V.: Laser cladding for crack repair of CMSX-4 single- crystalline turbine parts. Lasers in manufacturing and Materials Processing 4 (1), 13-23 (2017) [10] Rush, M.T., Colegrove, P.A., Zhang, Z., Courtot, B.: An investigation into cracking in nickelbase superalloy repair welds. Adv. Mat. Res. 89-91, 467-472 (2010) [11] Osterle, W., Krause, S., Moelders, T., Neidel, A., Oder, G., Volker, J.: Influence of heat treatment on microstructure and hot crack susceptibility of laser-drilled turbine blades made from René 80. Mater. Charact. 59, 1564-1571 (2008) [12] Osoba, L.O., Sidhu, R.K., Ojo, A.: On preventing HAZ cracking in laser welded DS Rene 80 supe- ralloy. Mater. Sci. Tech. Ser. 27 (5), 897-902 (2011) [13] Kim, H.I., Park, H.S., Koo, J.M., Seok, C.S., Yang S.H., Kim, M.Y.: Evaluation of welding characteris- tics for manual overlay and laser cladding materials in gas turbine blades. J. Mech. Sci. Technol. 26 (7), 2015-2018 (2012) [14] Ekrami, A., Moeinifar, S., Kokabi, A.H.: Effect of transient liquid phase diffusion bonding on micros tructure and properties of a nickel base superalloy Rene 80. Mat. Sci. Eng. A-Struct. 456, 93-98 (2007) [15] Barjesteh, M.M., Abbasi S.M., Madar, K.Z., Shirvani, K.: The effect of heat treatment on charac- teristics of the gamma prime phase and hardness of the nickel-based superalloy Rene 80. Mat. Chem. Phys. 227, 46-55 (2019) [16] Moralejo, S., Penaranda, X., Nieto, S., Barrios, A., Arrizubieta, I., Tabernero, I., Figueras, J.: A feedforward controller for tuning laser cladding melt pool geometry in real time. Int. J. Adv. Manuf. Technol. 89 (1), 821-831 (2016) 8 LASER CLADDING AsorCAD Engineering, S.L.. Interior Portada Dynamical 3D, S.A. ................ Contraportada Eceleni, S.L. ............... Interior Contraportada Grupo Solitium ................................................ 3 Maquinser ...................................................... 13 Renishaw Ibérica, S.A.U. ..............................29 Rösler International GmbH.......................... 27 Sicnova 3D ........................................... Portada SMD 3D Pantur, S.L.......................................35 Solid Perfil 3D, S.L................. Interior Portada